HOLDEN COMMODORE V8 5.7 LTR EFI
V6 Conversions have developed a conversion kit that allows the instillation of the Holden Commodore V8 5.7ltr EFI to the above vehicles. The kit is designed to replace the original grey/red motor & gearbox. The kit is designed to take the T700 or T5 gearbox. There is some cutting and welding required in the gearbox tunnel area. The instillation is carried out with the new front cross member.
We use a remanufactured rear mounted rack & pinion from a VB-VK Commodore which comes in our kit complete from tie rod end to tie rod end with all mounting brackets & bolts and instructions. With this steering kit you can use HR disc brakes or HQ-WB stub axles and brakes or we can offer you a stub axle that will accept VN-VP brake assembly.
The steering column used is up to the individual, in our instruction sheet we give you the measurements to convert the column or we have an exchange unit available.
It is up to the individual on which diff combination to run. However, we have available a VN-VT diff assembly that comes complete from disc to disc with Commodore stud pattern as a bolt in unit, or we can convert you own VN-VT diff to suit.
We have covered part of the brakes in the steering, we have found the best combination is to use a brake booster from a VB-VK Commodore mounted to the
firewall (the mounting bracket is supplied in our kit). You can either use the VB master cylinder or a VN master cylinder. This combination can be used with HR discs and drum or HQ-WB or VN-VP.
In our conversion kit we supply you with a gearbox cross member. With EJ-EH manual bodies, we use a heavy duty cross member which is secured in place with 6 bolts. The gearbox tunnel will require modification. When fitting the T700 the tunnel will need raising 20mm through the centre and the tunnel support will need to be removed and the ends will need to be capped.When fitting the T5 the tunnel requires major modification. With auto bodied EJ-EH’s there only needs to be a small amount removed from the tunnel support. The cross member supplied for the auto bodies is a weld on to the original cross member.
The wiring kit we have available covers from VN-VS, it comes in 2 parts, the under bonnet loom with all relays and fuses and the under dash loom which incorporates an engine trouble light. This wiring kit plugs into the original V8 engine and gearbox loom leaving only 6 wires to be tapped into your vehicles original loom, which are –
alternator light, oil light, temp light, ignition, starter & tacho.
Our speedo kit comes in 2 forms, an inline speed sensor and cable to suit VN-VP or an electronic speedo for VR-VS instillation.
It is best to use the original radiator, it is advisable to have the radiator serviced and run an overflow tank and recovery cap.
WIPER MOTOR CONVERSION/EJ-EH.
In our conversion kit we supply you with a drilling template to mount an LC-LJ wiper motor assembly, you should use the wiper switch from the LC-LJ.
An Engineers report is required after the conversion has been completed, contact your local RTA office for a list of Engineers in your district.
Requirements for Engineering are that seat belts must be fitted plus a heater demister.
You will need to obtain the following components –
* The Commodore V8 engine complete with the main engine wiring harness, the ECM. Other accessories such as the map sensor, purge canister, air cleaner & ducting, engine pipes & catalytic converter, external fuel pump & damper,
gearbox & gearbox wiring harness and gearshift assembly.
* Independent Front End
* gearbox crossmember
* engine mounts
* speedo kit
* wiring kit
* header kit
* starter motor conversion
* 7″ brake booster kit
* hinge kit
EJ-EH 5.7 LTR V8 Kit with N.F.E$10,724.00 – $11,077.20